LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 2018 >> Charger Pursuit, 5.7L Eng VIN T, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (8HP45/845RE Automatic Transmission (Service Information)) >> Valve Body >> Installation

Valve Body: Installation

WARNING: This page is about a different variant/trim than selected.
CAUTION:

The Transmission Control Module (TCM), or Transmission Control Module Assembly (TCMA) is extremely sensitive to Electrostatic Discharge (ESD). Always use a ground strap and follow the ESD guidelines in ELECTROSTATIC DISCHARGE (ESD) SENSITIVE DEVICES. Failure to follow these instructions may result in damage to the TCM/TCMA.

GC0152241Courtesy of CHRYSLER GROUP, LLC
  1. Install the fluid port (1) with NEW  O-rings (2) and seal (3) to the valve body.
    GC0152262Courtesy of CHRYSLER GROUP, LLC
  2. Install the valve body assembly to the transmission using the previously installed (1) (special tool #10379, Pins, Valve Body Alignment) as a guide.
  3. Use an appropriate tool on one of the alignment pins to assist in holding the valve body in position while installing the remaining fasteners.
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  4. Install the valve body assembly retaining bolts not including 16-18 and hand tighten.
  5. Remove the pins and install the remaining bolts.
    GC0152117Courtesy of CHRYSLER GROUP, LLC
  6. Using (special tool #10377, Remover/Installer, Guide Sleeve) (1) carefully install the wire harness insulator (2) to the transmission case (3).
    GC0152103Courtesy of CHRYSLER GROUP, LLC
  7. Lock the wire harness connector lock (2) to the internal harness end.
  8. Install the rear valve body retaining bolts (1, 2) and tighten to the proper (Torque Specifications).
    GC0175210Courtesy of CHRYSLER GROUP, LLC
  9. When installing the OSS into the case, take care to position the OSS guide pin as shown below or DAMAGE  to the sensor may result. This is the INCORRECT  alignment of the pin.
    GC0175216Courtesy of CHRYSLER GROUP, LLC
  10. This is the CORRECT  installation and pin alignment.
  11. Install the sensor (4) to the case, install the bolt (1) and tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
  12. Install the valve body assembly end retainer bolts (3) and hand tighten.
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  13. Tighten the valve body bolts in the sequence shown to 8 N.m (71 in. lbs.).
    GC0152243Courtesy of CHRYSLER GROUP, LLC
  14. Remove the tie strap and return the manual park release lever (1) to the original position, tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
    GC0152239Courtesy of CHRYSLER GROUP, LLC
  15. Install the oil pan and gasket.
  16. Install the 13 oil pan retaining bolts and tighten the bolts in the sequence shown to 10 N.m (89 in. lbs.).
    GC0095860Courtesy of CHRYSLER GROUP, LLC
  17. All Wheel Drive (AWD) Vehicles  Install the crossmember (3), the crossmember to frame bolts (1) and tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
  18. All Wheel Drive (AWD) Vehicles  Install rear support bolts (2) and tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
  19. All Wheel Drive (AWD) Vehicles  Position the steering gear in place and tighten the bolts to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
    GC0152193Courtesy of CHRYSLER GROUP, LLC
  20. Connect the wire harness connector (1).
    GC0152192Courtesy of CHRYSLER GROUP, LLC
  21. Turn the locking mechanism (1) of the wire harness connector clockwise and lock it in place.
  22. If the valve body is replaced, program the Transmission Control Module (TCM). Refer to MODULE, TRANSMISSION CONTROL (TCM), MODULE PROGRAMMING .
  23. Fill the transmission. Refer to FLUID AND FILTER, STANDARD PROCEDURE .
  24. Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST .
scientia non olet · About LEMON Manuals