Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read the Body Control Module (BCM) DTCs and record on the repair order.
  Is the DTC active?
  
  Yes
  - Go To 2
  No
  - The condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension. If no problems are found, test complete.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE RUN RELAY
1. Turn the ignition off.
2. Remove the Run Relay from the Rear Power Distribution Center (PDC) and substitute it with a known good relay.
3. With the scan tool, read DTCs.
  Does the scan tool display this DTC as active?
  
  Yes
  - Go To 3
  No
  - Replace the Run Relay.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (K619) RUN RELAY CONTROL CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Remove the Run Relay from the Rear PDC.
  NOTE:
  The test light must illuminate brightly. Compare the brightness to that of a direct connection to the battery.
3. Using a 12-volt test light connected to ground, check the (K619) Run Relay Control circuit at the Run Relay in the Rear PDC.
  Does the test light illuminate brightly?
  
  Yes
  - Go To 6
  No
  - Go To 4
CHECK THE (K619) RUN RELAY CONTROL CIRCUIT FOR AN OPEN
1. Disconnect the BCM C5/E harness connector.
2. Measure the resistance of the (K619) Run Relay Control circuit between the Run Relay in the Rear PDC and the BCM C5/E harness connector.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Go To 7
  No
  - Go To 5
CHECK THE (Z922) GROUND CIRCUIT FOR AN OPEN
1. Measure the resistance of the (Z922) Ground circuit between ground and the Run Relay terminal in the Rear PDC.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Go To 8
  No
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE REAR PDC FOR AN INTERNAL SHORT TO VOLTAGE
1. Disconnect the Rear PDC C2 harness connector.
2. Using a 12-volt test light connected to ground, check the (K619) Run Relay Control circuit at the Run Relay terminal in the Rear PDC.
  Does the test light illuminate brightly?
  
  Yes
  - Go To 9
  No
  - Repair the short to voltage in the (K619) Run Relay Control circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE REAR PDC FOR AN INTERNAL OPEN (K619) RUN RELAY 2 CONTROL CIRCUIT
1. Disconnect the Rear PDC C2 harness connector.
2. Measure the resistance of the (K619) Run Relay Control circuit between the Run Relay terminal in the Rear PDC and the Rear PDC C2 harness connector, component side.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Go To 9
  No
  - Repair the open in the (K619) Run Relay Control circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE REAR PDC FOR AN INTERNAL OPEN (Z922) GROUND CIRCUIT
1. Disconnect the Rear PDC C2 harness connector.
2. Measure the resistance of the (Z922) Ground circuit between the Run Relay terminal in the Rear PDC and the Rear PDC C2 harness connector, component side.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Go To 9
  No
  - Repair the open in the (Z922) Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
REAR POWER DISTRIBUTION CENTER (PDC)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors of the Rear PDC.
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for signs of water intrusion, corrosion, pushed out, bent or broken terminals. Verify that there is good pin to terminal contact in the Rear PDC harness connectors.
4. Perform any Technical Service Bulletins (TSB)s that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Replace the Rear Power Distribution Center (PDC) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .