LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 2018 >> Charger Pursuit, 5.7L Eng VIN T, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (6.4L Engine (Service Information)) >> Lubrication >> Pan, Oil >> Installation

Pan, Oil: Installation

WARNING: This page is about a different variant/trim than selected.
GC0080323Courtesy of CHRYSLER GROUP, LLC
NOTE:

Mopar® Engine RTV must be applied to the 4 T-joints, the area where the front cover, rear retainer and oil pan gasket meet. The bead of RTV should cover the bottom of the gasket. This area is approximately 4.5 mm x 25 mm in each of the 4 T-joint locations.

  1. Clean the oil pan gasket mating surface of the engine block and oil pan.
  2. Apply Mopar® Engine RTV at the 4 T- joints (1, 2).
    GC0144561Courtesy of CHRYSLER GROUP, LLC
    NOTE:

    When the oil pan is removed a NEW oil pan gasket and the integral windage tray assembly must be installed, the old gasket cannot be reused.

  3. Install a NEW oil pan gasket/windage tray (3).
  4. Using a NEW O-ring, position the oil pump pickup tube (2) into the oil pump.
  5. Install the oil pump pickup tube retaining bolt and nut (1) and tighten to the proper specification. Refer to TORQUE SPECIFICATIONS  .
    Fig 1: Oil Pan Tightening Sequence
    GC0095578Courtesy of CHRYSLER GROUP, LLC
    NOTE:

    The horizontal M10 retaining bolts (11, 12, 15, 18) are 5 mm longer in length then the vertical M10 retaining bolts (20, 21, 22, 23) and must be reinstalled in their original locations.

    NOTE:

    New M6 retaining bolts must be used when reinstalling the oil pan. Do not reuse the old M6 retaining bolts.

  6. Align the rear of the oil pan with the rear face of the engine block and install the M10 and M6 retaining bolts finger tight.
  7. Using the sequence shown, tighten the M6 retaining bolts to 5 N.m (44 in. lbs.).
  8. Using the sequence shown, tighten the M10 retaining bolts to 54 N.m (40 ft. lbs.).
  9. Using the sequence shown, tighten the M6 retaining bolts to 12 N.m (9 ft. lbs.).
  10. Lower the vehicle.
    GC0094863Courtesy of CHRYSLER GROUP, LLC
  11. Using the Engine Lift Fixture (special tool #8984B, Fixture, Engine Lifting) (1), Engine Lift Adapter (special tool #8984-UPD, Adapter, Engine Lift) (2) and the Engine Support Fixture (special tool #8534C, Fixture, Driveline Support) (3) lower the engine into position and remove.
  12. Install the engine oil dipstick tube and dipstick.
  13. Raise the vehicle.
    GC0144614Courtesy of CHRYSLER GROUP, LLC
  14. Install both engine mount lower retaining bolts (2) and tighten to the proper specification. Refer to TORQUE SPECIFICATIONS  .
  15. Position both engine mount heat shields (4) and install retaining nuts (3).
    GC0080538Courtesy of CHRYSLER GROUP, LLC
  16. Position the steering gear (2), install mounting bolts (1) and tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
    GC0148457Courtesy of CHRYSLER GROUP, LLC
  17. Lightly lubricate the oil filter gasket with clean engine oil.
    NOTE:

    Do not over tighten the oil filter.

  18. Thread the oil filter (1) onto the oil cooler (2) oil filter boss.
  19. When the oil filter gasket makes contact with the oil cooler sealing surface, hand tighten the oil filter one half turn, or 180°.
    GC0095584Courtesy of CHRYSLER GROUP, LLC
  20. Position the belly pan to the under side of vehicle and install belly pan retainers (1).
  21. Lower the vehicle.
  22. Install the intake manifold. Refer to MANIFOLD, INTAKE, INSTALLATION .
  23. Fill the engine with oil. Refer to OIL  .
  24. Connect the negative battery cable.
  25. Start the engine and check for leaks.
scientia non olet · About LEMON Manuals