Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
NOTE:
Diagnose and repair any system voltage DTCs before continuing with this test.
1. Start the engine and allow it to idle.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
2. With the scan tool, read DTCs.
  Is the DTC active?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
FUEL INJECTOR 2 WIRING AND CONNECTOR INSPECTION
1. Turn the ignition off.
2. Verify that the connector is properly connected to the injector.
3. Disconnect the Fuel Injector harness connector and inspect the wiring and terminals for any condition that would result in a poor connection.
4. Look for any chafed, pierced, pinched, or partially broken wires.
5. Look for broken, bent, pushed out or corroded terminals.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (F342) FUSED ASD RELAY OUTPUT CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition on.
2. Using a 12-volt test light connected to ground, check the (F342) Fused ASD Relay Output circuit in the Fuel Injector 2 harness connector.
  NOTE:
  The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
  
  Is the test light illuminated and bright?
  
  Yes
  - Go To 4
  No
  - Repair the (F342) Fused ASD Relay Output circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE (K12) INJECTOR 2 CONTROL CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the Fuel Injector 2 harness connector.
3. Check for continuity between ground and the (K12) Injector 2 Control circuit in the Fuel Injector 2 harness connector.
  Is there continuity between ground and the (K12) Injector 2 Control circuit?
  
  Yes
  - Repair the (K12) Injector 2 Control circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK THE (K12) INJECTOR 2 CONTROL CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Disconnect the PCM C2 harness connector.
  CAUTION:
  Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.
2. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
3. Measure the resistance of the (K12) Injector 2 Control circuit between the Fuel Injector 2 harness connector and the GPEC Adaptor.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (K12) Injector 2 Control circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
FUEL INJECTOR 2
1. Turn the ignition off.
2. Measure the resistance of Fuel Injector 2.
  NOTE:
  The resistance of the Fuel Injector will vary according to the temperature of the injector coil.
  
  Is the resistance of the Fuel Injector between 9.0 and 18.0 ohms?
  
  Yes
  - Go To 7
  No
  - Replace Fuel Injector 2 in accordance with the Service Information. Refer to INJECTOR(S), FUEL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between Fuel Injector 2 and the Powertrain Control Module (PCM).
  - Look for any chafed, pierced, pinched, or partially broken wires.
  - Look for broken, bent, pushed out or corroded terminals.
  - Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.
  - Look for the data to change or for the DTC to reset during the wiggle test.
  - Perform any Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .